Lowa Zephyr Mk 2 GTX

SABRE Introduces PenCott SnowDrift “Ghostwalker” Gear

December 5th, 2013

Germany-based SABRE Shop has just released their Special Forces Smock, Gen. III and Sniper Trousers, Gen. II in Hyde Definition’s PenCott SnowDrift pattern. The Special Forces Smock and Sniper Trousers were developed with input from the Sniper cadre at the International Special Training Center (formerly: International LRRP School) in Pfullendorf, Germany.

Special Forces Smock, Gen. III
99155be4e16fa55678c7b94fe51f475f_5

  • Material: 50/50 NyCo
  • Adjustable hood (can be rolled and is removable)
  • 2 chest pockets with bellows effect and flap with button opening
  • Opening of the top and sides possible
  • Small opening on the inside for easy cable management
  • Rubber strap inside to attach a radio
  • Opening in pocket flap for an antenna
  • 2 patch pockets with bellows effect and flap with button opening
  • Big patch, split with Velcro poachers pocket on the lower back
  • All 5 bellows pockets have the following features:
  • – Extended pocket openings to protect against falling out of material
    – D-rings
    – Cordura in the lower third of the pockets

  • 2 map pockets with zipper opening
  • Interior patch pockets with zipper opening
  • 2 patch upper sleeve pockets with bellows effect and side zipper opening
  • 2 lower patch pockets with sleeves side zip opening
  • Large rear inner compartment
  • Newly designed, tightly integrated magazine pockets
  • Opening by small wire reinforced – faster magazine change possible
  • Internal organization with loops for fasteners
  • Bottom pocket thirds and total cover of the bag reinforced with Cordura
  • Velcro patch on pocket for easy identification
  • Bars for reinforcement at stress points like pocket openings
  • Reinforced elbows with Cordura and removable poster
  • Additional internal zipper in the front bar for subsequent attachment of a Sabre Fleece Jacket
  • Underarm ventilation with zipper and mosquito net
  • Large covered buttons for easy handling
  • Cuffs with sewn windscreen adjustable with Drawcord
  • Optional end-to-use Springer Apron
  • One-hand drawstring at waist and hem
  • Concealable Velcro panels for attaching signs and patches
  • Sniper Trousers, Gen. II
    4d852e2bf5f6b93afd29e36f54715132_5

  • Material: 50/50 NyCo
  • Cordura knee reception area with an option for removable padding by pockets
  • High-cut kidney area
  • Removable suspenders
  • 2 cargo pockets on the back of the upper and lower leg
  • 2 side pockets with D-ring
  • Adjustable leg porch by elastic cord
  • One-hand cord lock
  • 50mm reinforced belt loops
  • All buttons are covered
  • www.sabre-shop.de/

    www.hydedefinition.com/

    MultiCam Family of Patterns Rollout Schedule

    December 5th, 2013

    Due to the large amount of inquiries for sample yardage as well as outright orders for the new MultiCam family if patterns, Duro released this update. Look for orders opening up during SHOT Show with MultiCam Black available now.

    20131205-070112.jpg

    www.multicamfabric.com

    Arsenal, Inc. Releases SM-13 To Public

    December 5th, 2013

    OLYMPUS DIGITAL CAMERA

    LAS VEGAS, NV – After the successful fulfillment of a military requirement, Arsenal, Inc. is excited to announce the release of the SM-13 to the commercial market. This one-piece side-attaching scope mount for the AK variant rifles was born to meet and exceed the toughest objectives put in front of Arsenal, Inc. The SM-13 was designed and manufactured specifically to surpass the following requirements:

  • To come up with a light-weight, precision, and highly rigid scope mount platform for military application: The one-piece CNC precision machined SM-13 is manufactured from aircraft grade aluminum alloy for the minimum weight (only 5.76 ounces) and maximum strength.
  • To have the maximum-length Picatinny railing system for attaching top mounted devices, such as scopes, red dot systems, night visions, and magnifiers: The over-7.5-inches-long Picatinny rail that runs along the rifle, from the end of the top cover to the rear sight leaf, allows for attaching multiple devices at the same time or one device for the maximum eye relief.
  • To have the lowest profile that adds the minimum to the bulk of the rifle and allows the use of iron sights while the mount is installed: The SM-13 follows the contour of the rifle closely. The absolute low profile and the relief cut along the rail allow the use of the iron sights even when the scope mount is attached to the rifle.
  • To have a quick-release attaching mechanism that provides the maximum stability and consistency: The SM-13 utilizes the time-proven steel adjustable locking mechanism that allows instantaneous attachment and release of the scope mount without any compromise to the accuracy and loss of zero. Unlike some other mounts that attach to unstable top covers or gas tubes, the SM-13 attaches to the side scope rail of an AK variant rifle, which provides the most stable attaching platform on the rifle.
  • The SM-13 is now available through distributors and retailers nationwide.

    www.arsenalinc.com/usa/SM-13_SCOPE-MOUNT

    www.arsenalinc.com/usa/

    Magpul Now Shipping Rail Light Mount And PMAG 10 LR/SR GEN M3

    December 5th, 2013

    NL_headerimage_MAG290

    Magpul is now shipping the Rail Light Mount and PMAG 10 LR/SR Gen M3 magazine.

    Rail Light Mount

    NL_productimage_MAG290_ODD

    The Rail Light Mount is constructed of reinforced polymer, and includes everything needed to mount SureFire 300 and 600 series Scout lights, 1913 Picatinny attachment pistol lights, and all light bodies from .75″ to 1.03″ in diameter thanks to the included set of anodized aluminum mounting rings. The mount is designed to fit on any standard 1913 Picatinny rail, is available in right or left side models, and integrates with the Magpul XTM panels. Its design positions the weapon light high and cantilevered forward, at the 11 o’clock or 1 o’clock position, to allow for a more forward support hand position, keep the light tucked in close to the bore, and to minimize barrel shadow. A textured thumb ramp is integrated to provide the user an index point, aiding consistent hand placement and light activation.

    Made in the USA.

    store.magpul.com/product/MAG498

    PMAG 10 LR/SR GEN M3 Magazine

    NL_productimage_MAG498_EVEN

    The PMAG 10 LR/SR GEN M3 brings GEN M3 technology to the 10-round 7.62×51 NATO/.308 Winchester magazine. Perfect for use with a bipod or when shooting off a pack, hunting applications, and also for States where overall capacity is limited.

    Made in the USA.

    store.magpul.com/product/MAG290

    magpul.com/

    Social Hand Grenade

    December 5th, 2013

    Social Hand Grenade

    Social Hand Grenade is a clothing brand owned and managed by UK-based Intelligent Armor Limited. Their product line includes t-shirts, polo shirts, jumpers, and accessories for men, women, and children, most of it made from natural 100% cotton or bamboo. All designs and logos are screen printed within the UK.

    www.social-hand-grenade.com/

    Sierra 7 Bipods

    December 4th, 2013

    S7

    Billed as ‘The World’s Finest Bipod’, the S7 bipod was developed by active duty soldier and competitive shooter Daniel Horner. It’s designed to give the modern sniper, who is employing larger caliber and more accurate rifles, a suitable support.

    Pan

    The Sierra 7 has a pan feature that allows for unparalleled precision. There is no play in any direction which makes engaging moving targets and transitioning from target to target easier. The S7 has a tension lever on the rear that allows the tracking feature to be tensioned from free to locked, and in-between, in 3/8 of a turn. There is a total of 90 degrees of panning, 45 degrees in each direction, and a rugged stop on each side ensures the rifle is always supported.

    Tilt

    The tilt feature on the S7 allows the bipod to rotate smoothly regardless of the amount of tension applied to the mechanism. The tension is adjustable from completely free to completely locked in 3/8 of a turn, with an infinite amount of tension adjustment in-between. The S7 features a total of 60 degrees of tilt, 30 degrees in each direction.

    Leg-Extended

    The outer tubes of the legs on the S7 are machined from steel. This allowed Sierra 7 to make a leg with virtually no play. Taking into account the variety of environments the bipod could be deployed in, there is enough room for dirt and debris to fall away, and a powerful spring pushes the inner legs out.

    Feet

    The S7 can be outfitted with two types of feet: the rugged, reliable, and time-tested rubber feet, and the S7 Raptor Claws. The Raptor Claws are an original concept by Sierra 7, designed to enhance the user’s shooting position when ‘loading’ the bipod or trying to grab onto any type of footing. In fact, with the S7’s legs locked in the 45 degree position, with Raptor Claws attached, and the bipods ‘loaded’, it becomes much easier for the shooter to regularly watch their own trace.

    The S7 bipod is available for sale directly from Sierra 7 Bipods. Made in the USA from US materials.

    www.sierra7bipods.com/

    More BAE Systems Body Armor Headed To Warfighters On The Battlefield

    December 4th, 2013

    PHOENIX, Arizona — For more than four decades, BAE Systems has partnered with customers worldwide to develop affordable, practical solutions to protect warfighters in harm’s way and bring them home safely. Under several recently issued contracts valued at a total of nearly $18 million, BAE Systems will continue to provide hard armor inserts for soldiers on the battlefield.

    ESAPI

    “The body armor is designed with the specific purpose of stopping armor-piercing bullets,” said Ashoo Agarwal, a quality engineer at BAE Systems. “Our team of engineers works hard to ensure every plate we make meets a rigorous set of requirements and standards. This commitment to quality helps protect warfighters around the world.”

    Among the contracts issued is a $10.2 million order from the U.S. Defense Logistics Agency for Enhanced Small Arms Protective Inserts (ESAPI); an Indefinite Delivery, Indefinite Quantity contract award for up to $6 million from the U.S. Department of Defense for SPEAR BALCS inserts and a $500,000 research and development contract from the U.S. Marine Corps for Enhanced Concealable Small Arms Protective Inserts.

    IMG_2499

    Hard armor inserts are worn inside the fronts, backs, and sides of outer tactical vests and provide advanced torso protection against increased threats on the battlefield. They are fully qualified by the U.S. government through arduous and independent physical, environmental, and ballistic testing.

    Since 1998, BAE Systems has produced more than 1.2 million hard body armor inserts, including ESAPI and other SAPI derivatives, under various Department of Defense contracts. BAE Systems manufactures body armor at its Phoenix, Arizona facility. Deliveries on these orders are expected to be complete by April 2015.

    www.baesystems.com/

    NRA News Commentators – Dom Raso – Episode 35 “Vets”

    December 4th, 2013

    Dom Raso highlights a bureaucratic flaw that’s unfairly stripping veterans of their Second Amendment rights — and tells you how to help get it fixed.

    A transcription of the video:

    Under Obama’s administration, there’s been a serious downsizing of our military. I’ve got my own thoughts on that, but I’ll save them for another time. Reality is, we’ve got a large number of people getting out of the military with a ton of combat and military experience; men and women being thrown back into civilian life. There have been several incidents already involving these vets and their rights being taken away from them.

    Recently, there was a vet that had to defend his home from a felon who was trying to break in. He fired a warning shot in the ground to scare the guy off and then told the police that his military training kicked in. Now whether that’s true or not, or even if he went into combat mode, the guy was having his house broken into. He clearly stated to the guy that was trying to force entry into his home and that he was going to give him a warning shot if he didn’t stop his forward progress. All he did was fire a warning shot into the ground, and then the criminal ran off.

    But the focus wasn’t on the convicted felon trying to break into his house; it was on the veteran who did everything possible to safely defend his home. The police actually took his gun away. There is something seriously wrong with our system if we are stripping his gun away because according to the police, he wasn’t justified to discharge a round. According to our oh-so-knowledgeable vice president, that’s exactly what he should be doing to ward off would-be attackers and burglars. Sounds like our vice president is giving us some false info.

    That was an unfortunate situation that affected one person, but I also want to talk about a serious problem that’s resulting in many more vets losing their Second Amendment rights for no reason. When a vet is eligible for disability compensation or other benefits, they go through an evaluation process. The way it’s set up right now, if the vet has someone else appointed to manage those benefits on their behalf, they somehow get labeled “mentally defective” and are entered into a background check system as someone unable to buy a gun. This is absolutely wrong. The VA’s review process for assigning a bookkeeper to a veteran in no way determines whether that veteran poses a risk to himself or others. It’s only meant to determine whether or not a veteran needs help managing his or her VA benefits. That has nothing to do with their ability to safely exercise their Second Amendment rights.

    More than 100,000 veterans and their family members have been affected by this problem. You can’t just take someone’s right away to bear arms because they need help in other areas. When these guys were overseas risking their young lives for our freedom, the government had no problem putting an M4 in their hands and letting them fend for themselves. So the very idea that that same government would let some paperwork nonsense strip them of their rights that they fought for, is absolutely disgusting.

    After you watch this video, I urge you to contact your senator either on the phone or online and let them know that this is a real issue they ought to be spending some time fixing. It’s unbelievable that they’re wasting time talking about useless, unconstitutional gun control laws when there are veterans out there being striped of their rights because of some paperwork problem. So call your senator, and let’s get this fixed.

    Call your senators and ask them to support Senate Bill 572, which will correct this injustice.

    Capitol Switchboard: (202) 224-3121

    www.nranews.com/commentators/video/episode-35-vets-with-dom-raso