SureFire

Archive for March, 2020

Army Scientists Create Innovative Quantum Sensor – Covers Entire RF Spectrum

Saturday, March 21st, 2020

ADELPHI, Md. — A quantum sensor could give Soldiers a way to detect communication signals over the entire radio frequency spectrum, from 0 to 100 GHz, said researchers from the Army.

Such wide spectral coverage by a single antenna is impossible with a traditional receiver system, and would require multiple systems of individual antennas, amplifiers and other components.

In 2018, Army scientists were the first in the world to create a quantum receiver that uses highly excited, super-sensitive atoms–known as Rydberg atoms–to detect communications signals, said David Meyer, a scientist at the U.S. Army Combat Capabilities Development Command’s Army Research Laboratory. The researchers calculated the receiver’s channel capacity, or rate of data transmission, based on fundamental principles, and then achieved that performance experimentally in their lab–improving on other groups’ results by orders of magnitude, Meyer said.

“These new sensors can be very small and virtually undetectable, giving Soldiers a disruptive advantage,” Meyer said. “Rydberg-atom based sensors have only recently been considered for general electric field sensing applications, including as a communications receiver. While Rydberg atoms are known to be broadly sensitive, a quantitative description of the sensitivity over the entire operational range has never been done.”

To assess potential applications, Army scientists conducted an analysis of the Rydberg sensor’s sensitivity to oscillating electric fields over an enormous range of frequencies–from 0 to 10^12 Hertz. The results show that the Rydberg sensor can reliably detect signals over the entire spectrum and compare favorably with other established electric field sensor technologies, such as electro-optic crystals and dipole antenna-coupled passive electronics.

“Quantum mechanics allows us to know the sensor calibration and ultimate performance to a very high degree, and it’s identical for every sensor,” Meyer said. “This result is an important step in determining how this system could be used in the field.”This work supports the Army’s modernization priorities in next-generation computer networks and assured position, navigation and timing, as it could potentially influence novel communications concepts or approaches to detection of RF signals for geolocation.

In the future, Army scientists will investigate methods to continue to improve the sensitivity to detect even weaker signals and expand detection protocols for more complicated waveforms.

The Journal of Physics B published the research, “Assessment of Rydberg atoms for wideband electric field sensing,” in its special issue on interacting Rydberg atoms. Army scientists David H. Meyer, Kevin C. Cox and Paul D. Kunz led this research, as well as Zachary A. Castillo from the University of Maryland. This work was supported by the Defense Advanced Research Projects Agency.

By US Army CCDC Army Research Laboratory Public Affairs

Special Tactics Airman Involved In Fatal Swim Training Incident Identified

Saturday, March 21st, 2020

HURLBURT FIELD, Fla. – Airman First Class Keigan Baker, 24, an Air Force Special Tactics combat controller assigned to the Special Tactics Training Squadron, 24th Special Operations Wing, was found unresponsive after he went missing during a surface training swim at Naval Support Activity Panama City, Florida, Thursday.

Baker was taking part in the Air Force Combat Dive Course run by Air Education and Training Command’s Special Warfare Training Wing headquartered at Joint Base San Antonio-Lackland.

“This is devastating loss to the entire Special Tactics community,” said U.S. Air Force Col. Matthew Allen, commander of the 24th SOW. “We are very grateful for Keigan’s willingness to serve our nation and vow to honor his memory.”

The agencies that contributed to the search and recovery efforts include: The Naval Diving and Salvage Training Center, U.S. Coast Guard Station Panama City, Bay County Sheriff’s Office, The Florida Fish and Wildlife Conservation Commission and other sister service dive units.

Baker enlisted in the United States Air Force in June 2018 and was recognized as an Honor Graduate at Basic Military Training. After BMT, he immediately entered the two-year combat control training program. Shortly after being assigned to STTS he left to attend the Special Warfare Pre-Dive course at Joint Base San Antonio-Lackland, followed by the Air Force Combat Dive Course at Naval Support Activity Panama City, Florida.

The Air Force Combat Dive Course teaches students diving fundamentals through open circuit self-contained underwater breathing apparatus (SCUBA) training and closed circuit underwater breathing apparatus (UBA) training. Students learn basic diving, advanced rescue diving principles and advanced combat diving fundamentals. Upon completion of the course, students are certified Special Operations Command (SOCOM) combatant divers.

“Keigan’s loss is felt across the entire training wing, where the safety of our trainees is our top priority,” said U.S. Air Force Col. Parks Hughes, commander of the Special Warfare Training Wing. “We are grateful to all the agencies that assisted with the search and recovery effort.  Our thoughts and prayers are with Keigan’s family, friends and teammates.”

The Longview, Washington native was a graduate of Mark Morris High School. He then received his Bachelors of Arts Degree in Business Administration from Eastern Washington University. 

His awards and decorations include: Air Force Good Conduct Medal, Air Force Basic Military Training Honor Graduate Ribbon, The Air Force Training Ribbon and the Global War on Terrorism Service Medal.

As a Special Tactics combat controller apprentice, Baker was training to deploy into combat zones to conduct reconnaissance, global access, precision strike and personnel recovery operations.

The incident is currently under investigation. For further queries on the incident and training please reach out to the Special Warfare Training Wing at SWTW.Public.Affairs@us.af.mil

Hudson Supplies Special Offer and News Update

Saturday, March 21st, 2020

In order to support our customers, we will be offering 19% off on everything we have in stock from www.hudson4supplies.com

Effective March 20th until further notice (no worries this will last a few weeks!). This is valid for all online orders only and while supplies last.

COUPON CODE: COVID19

Even more we have stock of ITW Clash Hooks (Made in USA) and ITW MQRB (Made in USA), they are available at discount price WQL.
Other items as well, for latest Update from Hudson Supplies (Coronavirus Covid19) and current promotions:
www.hudson4supplies.com/coronavirus-covid19

SureFire Spotlight – The WARCOMP

Saturday, March 21st, 2020


The revolutionary SureFire WARCOMP flash hider is the world’s most shootable flash hider. Its patent-pending design provides three valuable functions:

-It provides over 99% reduction in muzzle flash compared to a plain muzzle, which helps to conceal the shooter’s location and preserve his dark-adapted vision.

-It virtually eliminates muzzle rise, which enhances monitoring of target reaction and staying on target for faster follow-up shots.

-It serves as a rock-solid mounting adapter for all SureFire SOCOM Series Fast-Attach® suppressors, including our SOCOM556-RC model, which placed first in the most extensive and rigorous suppressor testing ever conducted by US Special Operations Command.

www.surefire.com






Rheinmetall: Strong Defence Sector Compensates for Weak Automotive Market

Saturday, March 21st, 2020

Fiscal 2019

•Consolidated sales grow by 1.7% to €6,255 million

•Consolidated operating earnings increase to new record of €505 million

•Order backlog rises to nearly €11 billion

•Operating free cash flow climbs to €314 million

•Dividend to be raised from €2.10 to €2.40

Outlook 2020 before effects of corona developments

•Group operating margin of approximately 7% anticipated

•Automotive expects an operating margin of approximately 5% as the market continues to decline

•Defence anticipates sales growth of between 5% and 7% and a margin of between 9% and 10%

•Annual forecasts will be adjusted if and when necessary due to the potential consequences of the global spread of the coronavirus

Following an overall successful fiscal year, Rheinmetall AG in Düsseldorf plans to raise its dividend by €0.30 to €2.40. The technology group once again recorded growth in both sales and income in fiscal 2019. This is primarily due to the positive business performance of the Defence sector, but Automotive showed robust performance in a weak market environment with overall declining passenger car production.

Armin Papperger, Chief Executive Officer of Rheinmetall AG: “With our profitability and full order books in Defence, our cost efficiency in Automotive and the Group’s financial resources, we are well prepared for the challenges we face. In Defence, we see good opportunities for continuing growth and high profitability. We want to make consistent use of the possibilities provided by military customers around the globe and to keep building on our leading positions. In Automotive, we are in a good position to build on our earlier success once the global automotive markets stabilize after the corona crisis. We will continue to benefit from rising demand for environmentally friendly mobility with our products for reducing consumption and emissions. At the same time, we are selectively expanding our activities in the field of alternative drives, so that we can continue playing an important role as a development partner to the international automotive industry in the future.”

Consolidated operating earnings exceed €500 million for the first time ever in 2019 – proposed dividend of €2.40 per share

In fiscal 2019, Rheinmetall increased its consolidated sales by €107 million or 1.7% year-on-year to €6,255 million. Adjusted for positive currency effects and sales from M&A activities, consolidated sales grew by 0.5%.

The sales growth in fiscal 2019 can be attributed exclusively to increased revenue in the Defence sector, which increased its sales by €301 million or 9.4%. By contrast, sales in the Automotive sector were €194 million lower than the previous year’s figure owing to the declining trend in global automotive production in 2019.

At 69%, the international share of consolidated sales in fiscal 2019 was slightly lower than in the previous year (72%).

In fiscal 2019, Rheinmetall increased its consolidated operating earnings (EBIT before special items) to over €500 million for the first time ever. At €505 million, they were up 2.9% compared with the previous year’s figure of €491 million. The operating margin also improved slightly compared with last year to 8.1% (previous year: 8.0%).

Including positive special items of €7 million net, reported EBIT for the Group amounts to €512 million. Special items resulted from restructuring costs at a Defence location (€-2 million), from a real estate transaction at the Berlin site (€+2 million) and due to insurance payouts (€+7 million). Reported EBIT is therefore only slightly lower than the previous year’s figure of €518 million, which included large, positive special items of €27 million net due chiefly to real estate transactions.

At €354 million, earnings after taxes were the same as in the previous year. After deduction of earnings of €19 million attributable to non-controlling interests (previous year: €49 million), earnings attributable to shareholders of Rheinmetall AG were €335 million. This represents an increase of 9.8% compared with the previous year’s figure of €305 million. Excluding the earnings attributable to non-controlling interests, earnings per share for 2019 amounted to €7.77, compared with €7.10 in the previous year.

The Group’s operating free cash flow increased significantly due to considerable improvements in working capital in particular and rose to €314 million after €-35 million in fiscal 2018.

The Group’s order backlog is more than €10 billion for the first time. On December 31, 2019, Rheinmetall had orders of almost €10,846 million on its books, which equates to growth of 20% compared to the order backlog of €9,055 million in the previous year (December 31, 2018).

The Executive Board and Supervisory Board will propose increasing the dividend to €2.40 per share at the Annual General Meeting on May 5, 2020. This corresponds to a distribution ratio of approximately 31%. A dividend of €2.10 per share was paid in the previous year.

Automotive robust in a weak market environment – operating margin of 6.7%

Rheinmetall Automotive’s performance was influenced by weaker business in the international automotive industry again in 2019. Automotive’s sales sank from €2,930 million in 2018 to €2,736 million in 2019, a reduction of 6.6%. According to the latest market data, global automotive production shrank by nearly 6% in the same period.

All three sector divisions suffered a decline in sales compared with the previous year. Due to the weak performance of the international automotive industry, the ongoing drop in demand for diesel products for the passenger car market was not offset, as in the previous year, by other product groups such as applications for trucks and gasoline drives. As a result, new product launches were postponed or took place on a much smaller scale than anticipated.

In the Mechatronics division, sales declined in the Automotive Emission Systems and Solenoid Valves product areas in particular. In the Hardparts division, sales of small-bore pistons declined in the markets of North America and Brazil, while the European sales market proved weak with regard to plain bearings. In contrast, the Aftermarket division performed well in its global markets overall, with only a slight drop in sales.

The joint ventures in China, which are not included in Rheinmetall AG’s consolidated sales, generated sales totaling €1,010 million in fiscal 2019. Compared with the previous year, this represents growth of 16%. Once again, the companies therefore significantly outperformed the Chinese passenger car market, which registered a 4% decline in production in 2019.

As a result of the drop in sales, the operating earnings of Rheinmetall Automotive (EBIT before special items) amounted to €184 million in the past fiscal year, after a record high of €262 million in the previous year. The operating margin consequently fell to 6.7% after 8.9% in the previous year.

Defence increases margin to 9.8% with significantly higher earnings

Excellent order intake and backlog

The Defence sector’s business performance in 2019 was again characterized by the high worldwide demand in the military sector and by Rheinmetall’s successful positioning in major markets around the globe.

Rheinmetall Defence increased its sales to €3,522 million in the past fiscal year, growing by €301 million or 9.4% compared with the previous year’s figure. Taking into account exchange rate changes and M&A activities, organic growth was 7.6%.

This rise in sales was achieved through, among other factors, the launch of the major Land 400 Phase 2 project for the Australian armed forces and the shipment of transport vehicles to the German armed forces. In addition, the start-up of the major “Future Soldier System” project with the German armed forces contributed to a significant increase in sales in the Electronic Solutions division. The Weapon and Ammunition division, in contrast, suffered a slight year-on-year drop in sales – due primarily to export restrictions in the processing of international orders.

The sector’s order intake remained at a high level. For the second year in a row, the sector received orders for over €5 billion. In fiscal 2019, the order intake amounted to €5,186 million, after €5,565 million in the previous year, in which the largest single order in the company’s history – 211 Boxer vehicles for the Australian armed forces – with a volume of over €2 billion helped set a new order intake record.

Order intake in fiscal 2019 was largely influenced by the acquisition of the major Mechanised Infantry Vehicle (MIV) project, with a value of €1.4 billion, for the delivery of Boxer vehicles to the British armed forces. The book-to-bill ratio in 2019 was 1.5, underscoring the Defence sector’s excellent growth prospects over the coming years.

The order backlog as at December 31, 2019, was €10.4 billion. Compared with the previous year’s figure of €8.6 billion, this represents an increase of €1.8 billion or a good 21%.

The sector also significantly increased its earnings in 2019. The sector’s operating earnings (EBIT before special items) amounted to €343 million in fiscal 2019, after the previous year’s figure of €254 million. This represents an increase of €90 million or 35%. The operating margin therefore climbed from 7.9% to 9.8%.

Outlook 2020: Defence and Automotive develop differently

Due to the comparative lack of clarity regarding the development of global automotive production over the next few months, which is currently declining due to the global economic risks associated with the spread of coronavirus, the Rheinmetall Group, too, is subject to greater forecast uncertainty regarding sales and earnings performance.

Because of the prevailing uncertainties, the possible effects of the corona virus situation have not been taken into account in the current forecast data for the 2020 financial year.

Thanks to the ongoing dynamic growth of our Defence sector, Rheinmetall expects moderate group sales growth overall. Annual sales in the Rheinmetall Group are expected to grow organically and before currency effects by between 1% and 3%. This expectation is based exclusively on the stable growth prospects for the Defence sector. In contrast, with the decline in the automotive market for the third year in a row and based on the most recent experts estimates for the development of global automotive production, lower sales are expected in the Automotive sector in 2020.

Besides the risk of weaker macro-economic development in the eurozone countries, the results of tightened CO2 regulations in the European Union, and effects of Brexit, which cannot be fully assessed, the current situation in the automotive industry is characterized by volatility risks due to unresolved trade conflicts. Added to that are the risks caused by the currently unforeseeable economic consequences of the coronavirus.

Against a background of these uncertainties regarding the development of production in all important automotive markets, Rheinmetall agrees with the expert forecasts and also expects to see global automotive production decline over the course of 2020.

Sales of the Automotive sector will be decisively influenced by the development of production in the European, North American, and Asian automotive markets – and above all there, in China, the largest global market. On the basis of current market expectations, Rheinmetall anticipates that sales in the Automotive sector – compared with the previous year’s figure and before currency effects – will fall by between 2% and 3% in the current fiscal year.

For the Defence sector, Rheinmetall expects – assuming continuing, restrictive export approvals for key European locations – to see sales growth before currency effects of between 5% and 7%. This growth forecast is essentially based on the expected program and delivery schedules from existing orders in the Defence sector for the current fiscal year.

Group operating margin expected to be approximately 7%

For the Automotive sector, Rheinmetall expects an operating margin of around 5% in fiscal 2020 based on the expected decline in global automotive production and the resulting sales forecast for the sector.

Rheinmetall expects a further improvement in operating earnings in the Defence sector in 2020 and an operating margin of between 9% and 10%. Taking into account holding costs, the Rheinmetall Group’s operating margin amounts to around 7%.

The global spread of coronavirus means that, as things stand, the economic risks for fiscal 2020 are growing. Rheinmetall will monitor the potential impact and adjust the annual forecasts if and when necessary.

Statements and forecasts referring to the future

This release contains statements referring to the future. These statements are based on the current estimates and forecasts of Rheinmetall AG and the information currently available to it. The statements referring to the future are not to be understood as guarantees of the future developments and results that they describe. These instead depend on a number of factors. They involve various risks and uncertainties and are based on assumptions that may prove to be inaccurate. Rheinmetall does not undertake a commitment to update statements referring to the future made in this release.






Federal Ammunition Introduces Three New Top Gun 100-Packs

Friday, March 20th, 2020

ANOKA, Minnesota – March 18, 2020 – Make clay crushing convenient with Top Gun 100-Packs. Each pack contains four 25-count boxes. Shipments of this product have begun to arrive at dealers.

The new bulk offerings hold 100 consistent Top Gun target loads, which feature hard lead pellets, reliable Federal primers and specialized wad columns that produce even patterns that break more targets. Two 12-gauge 2 ¾-inch, 1 1/8-ounce, 3-dram equivalent loads, shot size No. 7.5 or 8 are offered is these bulk packs. A 20-gauge, 2 ¾-inch, 7/8-ounce, 2.5-dram equivalent, shot size No. 8 is also available.

Features & Benefits

• Convenient 100-round packs

• Hard pellets

• Consistent, reliable Federal primers

• Unique wad column produces consistent patterns

Part No. / Description / MSRP

TG12100 8 / 12 gauge 2 3/4 inch 1 1/8 ounce 3 dram eq, 8, 100 count / $37.99

TG12100 7.5 / 12 gauge 2 3/4 inch 1 1/8 ounce 3 dram eq, 7.5, 100 count / $37.99

TG20100 8 / 20 gauge 2 3/4 inch 7/8 ounce 2.5 dram eq, 8, 100 count / $37.99

Federal ammunition can be found at dealers nationwide or purchased online direct from Federal. For more information on all products from Federal or to shop online, visit www.federalpremium.com.






Eagle Industries – Operator Gun Belt in Woodland Camo

Friday, March 20th, 2020

Woodland is making a comeback and Eagle Industries has manufactured a run of their Operator Gun Belt with MOLLE in classic Woodland Camouflage. Additionally, Eagle plans matching pouches for these Woodland OGBs.

Made from MIL-SPEC 4088 Type XIII webbing, these belts feature a Cobra buckle with integrated D-Ring as well as two rows of PALS compatible webbing.

Offered in a variety of colors and patterns, these are sized Small – XLarge.

eagleindustries.com/operators-gun-belt-with-molle-attachment






SSD x MFT Giveaway Winners Announced

Friday, March 20th, 2020

Soldier Systems – Mission First Tactical Giveaway