TYR Tactical

Archive for January, 2025

Announcing the Launch of the Staccato HD Family of Pistols

Tuesday, January 14th, 2025

FLORENCE, Texas, January 14th, 2025 – Staccato, the creators of the Staccato 2011® pistol, Staccato Ammo, and Staccato Ranch, is excited to announce the introduction of an all-new family of 2011 pistol: Staccato HD.

Born out of direct feedback from Staccato’s elite law enforcement and government end users, the Staccato HD incorporates a wide array of new features and technology resulting in the most technologically advanced 2011 pistol design ever brought to market.

The HD’s grip module is built around the Glock pattern magazine, already widely used by the law enforcement community and commonly available to all shooters in the retail market.

The HD’s controls are fully ambidextrous, with dual-sided safety and slide release levers as well as a swappable magazine release. There are also forward thumb index points machined into both sides of the frame.

Our signature forward slide serrations have been re-designed to wrap over the top of the slide with a more aggressive profile, assisting manipulations from the front of the pistol while wearing gloves or under adverse conditions.

Internal upgrades include a buffered, flat-wire recoil system and active firing pin block. Our updated HOST optic mounting system allows direct-to-slide mounting for the most popular miniature red dot optics. The rear iron sight is mounted directly to the slide, forward of the optic to negate the need for BUIS-equipped plates or adapters.

The first pistol to launch in this family is the Staccato P4. The P4 is built around a footprint that’s become increasingly popular among both armed professionals and citizens alike: a 4-inch barrel and slide mated to a full-size grip. The P4 grip will accept any full-size Glock-pattern magazine, but will ship with 18-round, heat-treated carbon steel magazines finished in a low-friction coating.

Coming in spring of 2025, the Staccato P4.5, built on the same full-size frame, features a 4.5-inch DLC barrel with a “sight block” design that increases non-reciprocating weight at the muzzle to help reduce felt recoil while preserving the faster cycle speed of the 4-inch slide.  

The Staccato HD line has been extensively tested for reliability, endurance, and harsh environment conditions both at the factory and by the highest tiers of Federal Law Enforcement.

The Staccato HD P4 will be available for purchase on January 28th, with an MSRP of $2499, and the HD P4.5 to be released at $2699. The HD line offers a new, ruggedized option for 2011 users looking for reliability under the toughest conditions while still experiencing the world’s best shooting handgun. Only from Staccato. Please visit www.staccato2011.com/HD for more information.

CANSOFCOM Awards Suppressor Contract To Millbrook Strategic Sciences Inc.

Tuesday, January 14th, 2025

Ottawa, Canada, 15 January 2025 – Millbrook Strategic Sciences Inc., an emerging leader in additive manufacturing of market-disruptive suppressor technology, is proud to announce the recent award of a contract with options to supply state of the art suppressors to the Canadian Special Operations Forces Command (CANSOFCOM). This key contract underscores the company’s innovative excellence and will deliver a groundbreaking flow-through suppressor technology, significantly enhancing operational readiness and the health and safety of end-users.

This competitively awarded contract marks a significant milestone for Millbrook, underscoring the exceptional operational performance of this scalable suppressor technology. It is the culmination of years in innovation cycles—from initial concept leading to this procurement award—emphasizing the value of supporting domestically manufactured solutions. This achievement not only reinforces Millbrook’s role as an innovator in advanced technology but also supports Canada’s commitment to “buying Canadian” and strengthening local industries.

Millbrook Strategic Sciences Inc. is honored to support this important contract and remains committed to optimizing operational readiness for its valued customers. This award not only recognizes the dedication and hard work of our team but also serves as a catalyst for continued innovation and leadership in the field as we move forward.

Attention Military, Government and Law Enforcement Professionals:

We are proud to join forces with US-based Strategic Sciences LLC at SHOT SHOW 2025 and look forward to seeing you! This is an excellent opportunity to explore how this groundbreaking suppressor technology can support your mission.

Please contact Rolando Mata of Strategic Sciences LLC at rolando.mata@strategicsciences.us (US agencies) or Frank Paquette of Millbrook Strategic Sciences Inc. at frank@millbrookcanada.ca (Canada & International agencies).

We look forward to connecting with you at the Strategic Sciences LLC Booth 32002, Venetian Expo Level II, Law Enforcement Section.

Qore Performance Expands ICEFLASK Line with Release of ICEFLASK MOLLE Holster

Tuesday, January 14th, 2025

Knoxville, TN — Qore Performance continues to expand their IceAge Ecosystem of accessory holsters for their newest thermoregulation and hydration innovation, the ICEFLASK water bottle, with the release of the all-new ICEFLASK MOLLE Holster. ICEFLASK is a collaboration with Felix from Redbeard Tactical.

The ICEFLASK MOLLE Holster is almost identical to the ICEFLASK Wing Holster released at launch last month, except that it does not have the Velcro® lined wing. The ICEFLASK MOLLE Holster, as the name suggests, is perfect for mounting ICEFLASK Holsters on any MOLLE-equipped surface or equipment.

Key Features and Benefits of ICEFLASK:

  • Cooling/Heating/Hydration: ICEFLASK carries 500ml of water, 23 watts of conductive cooling, or 17 watts of conductive heating
  • Wearable: ICEFLASK is the exact dimensions of a PRC-152 MBITR radio and fits in any -152 compatible pouch in the NATO inventory
  • Stackable: ICEFLASK stacks and nests, making an ideal and ultra-efficient replacement for traditional, single-use “blue ice” blocks to keep food and drinks chilled in your favorite hard or soft side cooler
  • Made in USA: ICEFLASK is 100% Made in USA from US-sourced, FDA-certified, BPA-free, HDPE
  • Durable: ICEFLASK is built to last in austere, no-fail environments
  • Conformal: ICEFLASK’s ergonomically-optimized, body-curve geometry for comfort and efficient thermal exchange when worn against the body, is also ideal for external pack storage pockets
  • Threads: ICEFLASK uses the nearly universal 28-410 thread standard found on bottled Coca-Cola products for easy, improvised support in the field

ICEFLASK is proudly 100% Made in the USA from US materials, ICEFLASK MOLLE Holster is 100% Made in the USA from US materials by US citizens at Qore Performance HQ2 in Knoxville, TN. ICEFLASK and ICEFLASK Holsters are available now, exclusively at QorePerformance.com.

Army Preps for Second Phase of Armored Formation Network On The Move Pilot

Tuesday, January 14th, 2025

FORT RILEY, Kan. — In future operations, speed will equate to survivability, especially for armored formations — the Army’s most mobile and lethal force.

Commanders will need resilient high-capacity on-the-move (OTM) network connectivity, the foundation for mobile command and control (C2), to inform rapid decisions, swift maneuver and dispersed command post (CP) operations.

As part of the Army’s network transformation efforts, the service is preparing for the second phase of its Armored Formation Network (AFN) OTM Pilot, supported by the 1st Infantry Division, to inform the right combination of emerging commercial network technologies that best support these units and their fast-paced missions.

“This new equipment is providing a definite advantage,” said Lt. Col. Marreo Burch, senior division communications officer (G6) for 1st ID. “To give the commanding general and other senior leaders the ability to move around the battlefield and stay connected — especially with the adversary’s ability to detect the command post from just a sheer electromagnetic spectrum standpoint — increases our survivability [and lethality].”

The diverse set of emerging commercial AFN OTM and at-the-quick-halt pilot capabilities includes high-throughput low-latency satellite communications systems that operate in both geosynchronous and low Earth orbits. The kit also includes multi-band high-capacity line-of-sight (LOS) backhaul and mesh networking capabilities, commercial 5G LTE cellular, and secure Wi-Fi. Baseband systems include a Secure But Unclassified-Encrypted enclave to enable integration of Integrated Tactical Network data exchange.

Having the ability to leverage multiple transport options will not only enhance the unit’s operational flexibility but increase network resiliency, ensuring data can be exchanged in denied, degraded, intermittent, and low-bandwidth (DDIL) environments, including enemy jamming attempts.

“To be able to track the fight, not just over lower tactical internet [lower echelon radio-based networks], but now upper tactical internet (TI), on a digital common operational picture, and process all the information that comes in from those brigades, definitely provides the division commander and our senior leaders better visualization of the battlefield in large scale combat operations,” Burch said. “Instead of losing a major understanding of the battle moving from command post to command post, having that [upper TI] on-the-move keeps those commanders, those senior leaders, in the fight and provides [continual] battlefield circulation.”

NETWORK CONNECTIVITY INSIDE VEHICLES

In preparation for the pilot, the Army’s Project Manager Tactical Network (PM TN) and Project Manager Interoperability and Services (PM I2S), at the Program Executive Office Command, Control, Communications, and Network (PEO C3N) — in tandem with other Army organizations including the C2 Cross Functional Team, Army Futures Command — partnered with industry to integrate a wide variety of new commercial OTM network capabilities onto the 1st ID’s Humvees and Joint Light Tactical Vehicles. The intent, however, is for the AFN design to be a modular kit that can be incorporated into other platforms, including Armored Multi-purpose Vehicles and Strykers. Because of this modularity, units will also be able to quickly install, replace, or add components that better serve specific mission sets. The equipment provides a significant size-weight and power reduction compared to current capabilities, which is critical for armored vehicle integration and increased command post mobility.

The AFN OTM equipment set includes advanced software capabilities such as the Army’s automatic primary, alternate, contingency and emergency (auto-PACE) communications capabilities that simplify bandwidth diversity for Soldiers in the fight. During the 1st ID command post exercise (CPX) at Fort Riley, in November, held in preparation for the upcoming pilot, Burch got a first-hand look at the auto-PACE capability as he conducted operations inside one of the integrated vehicles.

“During my 45-minute ride, when one transport was degraded, it would auto-switch to the lower latency mode of transport while we were moving,” he said. “It made sure that the highest, most efficient means of communication transport was selected. It definitely helped with maintaining comms while on the move.”

SUPPORTING NETWORK MODERNIZATION

The Army is leveraging lessons learned and Soldier feedback from the first phase of the AFN OTM pilot, conducted at Fort Stewart, Georgia, in January 2022, to implement phase two. This second phase will be supported by 1st ID Headquarters, Division Artillery Brigade and 1st Brigade Combat Team Headquarters, during the units’ combat training center rotations at the National Training Center, Fort Irwin, California, later in fiscal year 2025.

Learning from combat training rotations helps to ensure the Army maintains a competitive advantage over its adversaries, including fighting in DDIL environments, use of the electromagnetic spectrum, protected communications, cyber security, and distributed C2 at echelon.  

During the AFN OTM Pilot phase two, Soldiers will evaluate solutions that are interoperable with the existing network, while providing a path to the future. Soldier feedback will inform decisions on enduring AFN OTM capability baseline and requirements using technologies that will also help shape other Army modernization efforts, such as command post modernization; C2Fix efforts that deliver simple, intuitive, mobile and lower signature solutions to current close-combat forces; and Next Generation C2 for future warfare.

Supporting the Army’s efforts to pull technical complexity up to division and above, the AFN OTM Pilot will evaluate the best distribution of networking capabilities within armored formations that provides value without over-burdening Soldiers at lower echelons.

ENHANCING CP MOBILITY

To prepare for future large scale combat operations, the Army has ceased developing large, static command posts, opting instead for more mobile command posts with faster setup and teardown, and better ability to conduct distributed operations. The AFN OTM equipment set includes expeditionary at-the-quick-halt satellite systems that deliver high-throughput low-latency command post network connectivity in minutes, providing units with faster command post displacement and maneuver, greater operational flexibility, and increased survivability compared to legacy equipment. Additionally, an aerial layer leverages variable height antennas to extend high-capacity LOS range, overcome LOS terrain challenges such a tree canopies, or enable units to hide from detection.

“The speed at which the enemy can [identify] us once we turn on all of our equipment and systems is really our biggest challenge,” said Maj. Adam Black, deputy G6, 1st ID, from inside one of the integrated vehicles during the CPX.

The commercial AFN OTM baseline kit enables the unit to better conduct dispersed communications, or the ability to spread out the command post operations, “so we can fight a command post separated over a country’s distance rather than just in one spot,” Black said. “Inevitably, we are going to be under contact, and that is what we have to prepare for. If [we operate dispersed and] we lose a specific section of our CP, we won’t lose the entire CP.”

As the Army continues to move network complexity to division echelons and relevant emerging network technologies require more bandwidth, armored formations will need reliable upper TI OTM communication solutions to execute decentralized C2, which will enable commanders to make timely and informed decisions on the battlefield and outmaneuver the enemy.

“As an armored unit, our biggest issue historically has been being able to communicate on upper TI across the battlefield,” said Chief Warrant Officer 2 Justin Carrier, network technician, 1st ID. “Because of the amount and types of transport [in this kit], I have faith that we can retain some form of [upper TI] network transport in any type of disruptive environment.”

By Amy Walker, Project Manager Tactical Network, PEO C3N, public affairs

Coming Soon from Magpul – TMAG 20 AR/M4 GEN M3

Tuesday, January 14th, 2025

As part of their annual pre-SHOT Show announcements, Magpul has involved the TMAG 20 AR/M4 GEN M3, a 20-round capacity version of their Transparent magazine technology.

Molded from a durable translucent material with an olive drab hue, it provides shooters the ability to visibly verify various ammunition types and the current round count. Featuring ribbed front and rear straps for improved purchase during magazine changes, the sides are left smooth to enhance visibility.

Due to the shorter length, the 20 rounders lack the high visibility spring and round count markings of the 30-round variant.

https://magpul.com/tmag-20-ar-m4-gen-m3.html

XTech Tactical Launches Extended Magazine and Collaboration Magazine Extension for Glock 43

Monday, January 13th, 2025

December 29th, 2024

Tempe, AZ – XTech® Tactical expands their Glock compatible magazines and magazine accessories with two additions for the Glock 43. The first is a plus 3 round magazine extension, the MTX® 43 +3. The second is the complete steel reinforced 9 round magazine, the MAG43-9™.

MTX®43 +3

Features:

-Stainless 17-7 Steel Spring

-Converts 6 round magazines to 9 rounds of 9mm

-Patented MTX® extension technology for flawless feeding and unmatched durability

-Texture and side scallop to pair perfectly with the Glock 43

-Lifetime Warranty

-MSRP $19.95 SKU: XT3031301

MAG43-9™

Features:

-Steel Reinforced Magazine Body

-Stainless 17-7 Steel Spring

-9 round 9mm capacity

-Patented MTX® extension technology for flawless feeding and unmatched durability

-Texture and side scallop to pair perfectly with the Glock 43

-Lifetime Warranty

-MSRP $32.95 SKU: XT3031301

With these two recent additions the company now offers standard and/or extended capacity options for the Glock 17, Glock 19, Glock 26, and Glock 43.

The MTX 43 +3 magazine was developed and tested in collaboration with Vickers Tactical & Tango Down. It will also be offered as a soon to be announced Vickers Tactical variant.

“Having had the privilege of working closely with Tango Down and Vickers Tactical, we are excited to release our first collaboration with our MTX 43 +3. Their model of supporting the Glock platform with strong value functional upgrades with no compromise to reliability or durability ideally reflects our brand values.  

We are committed to expanding our support for Glock pistols with many more magazines, extensions and magazine sleeves coming in 2025. All our products for Glock style pistols are designed to be passed down for generations and include our lifetime warranty,” stated company president, Jeremy Deadman.

www.xtechtactical.com

XTech® is a registered trademark of XTech Tactical, LLC

Glock is a registered trademark of Glock, Inc and has no affiliation to XTech Tactical

 

Double Tap Industries Acquires Caliber Armor: Leaders in Industry, Stronger Together

Monday, January 13th, 2025

MADISON, IND.— Double Tap Industries, the leading manufacturer of high-quality shooting, hunting, and gun range accessories is proud to announce its acquisition of Caliber Armor a prominent provider of high-performance body armor and personal protection solutions. This strategic move marks a significant milestone in Double Tap Industries’ mission to deliver cutting-edge, reliable equipment for professionals and enthusiasts alike.

The acquisition of Caliber Armor reinforces Double Tap Industries’ commitment to expanding its product portfolio and enhancing its capabilities in the tactical and personal defense market. Known for their exceptional quality and innovation, Caliber Armor’s products have earned a trusted reputation among first responders, security professionals, and civilians seeking superior protection.

“We are thrilled to welcome Caliber Armor into the Double Tap Industries family,” says Kyle Kempker, CEO of Double Tap Industries. “By combining our strengths, we can bolster each other’s growth while delivering even greater value to our customers. Caliber Armor’s expertise in protective body armor complements our existing portfolio perfectly, enabling us to better serve our customers with a more comprehensive range of products that enhance both safety and performance.”

For customers of both companies, the integration promises exciting advancements. Caliber Armor’s cutting-edge technologies will complement Double Tap Industries’ robust offerings, creating a comprehensive suite of solutions for diverse operational demands. Current customers of Caliber Armor can expect continued support and access to their favorite products, now with the added benefits of Double Tap Industries’ resources and expertise.

“We believe this partnership creates a win-win scenario for both brands and our customers,” added Kevin Strnatka, Founder of Caliber Armor. “Our combined resources and shared commitment to quality and innovation position us to achieve remarkable growth and continue pushing boundaries in our respective fields.”

Stronger together, stay tuned for what Double Tap Industries and Caliber Armor have in store for 2025!

Magpul Announces DAKA Range Bags

Monday, January 13th, 2025

Coming soon form Magpul, the new DAKA Range Bags are made from their proprietary DAKA materials and include Dual YKK Aquaguard zippers and RF-welded seams that keep the elements away from your gear.

Available in small (20-liter) and large (40-liter) sizes, they’re packed with pockets, elastic loops to hold magazines, and compartments for all your miscellaneous items. There’s even a hook-and-loop system inside to keep things organized. As a bonus, the top of the main compartment folds out into a work mat, so you can fine-tune your gear without scratching it. 

Available in Black with FDE to follow – at Magpul.com or a local retailer near you soon.